https://stigodiy.bigcartel.com Hard to find repair parts, custom designs, products produced using 3D printers, injection molding, CNC machining and CNC plasma. 115553778 Pizza Oven Plans (no text) Gas Grill Pizza oven digital plans. Pizza oven works with 15 inch pizza stone, size of oven is 22.5 inch wide x 16 inch deep x 3 inch high. The plans include a .DXF file for use on a CNC plasma cutter and a "E" size .PDF of the oven at 1:1 scale, in both bent up and flat pattern versions to allow manual hand cutting of the oven for people who don't have access to a CNC table. For the hand cutting DIY'er, take the .PDF file to a local printer like Office Depot and get the "e" size print made and then use the 1:1 print as a template to mark the cut lines on the sheet metal. The plans are suitable for sheet thickness between 3/32" to 3/16". Material can be low carbon steel, which will require seasoning with vegetable oil to prevent rusting or it can be made out of a stainless steel. The plans are sent to the email of the purchaser within 1 business day of purchase. 10.00 USD https://stigodiy.bigcartel.com/product/pizza-oven-plans-no-text https://assets.bigcartel.com/product_images/411648789/IMG_9838.JPG https://assets.bigcartel.com/product_images/411648786/IMG_7063.JPG,https://assets.bigcartel.com/product_images/411648792/IMG_7204.JPG 115553778 new in stock 114130653 Shopsmith non-OEM rack gear replacement This is a injection molded replacement for the plastic rack on Shopsmith main carriage. The OEM has the rack gear in two pieces which are riveted on. This non-OEM gear will replace the OEM gear however new holes will need to be drilled, only one hole is reused to properly position the rack. The increase in rivet attachments will reduce the amount of rack bowing and subsequent failure on load that the OEM rack displayed. The rack sections snap together to assure the proper spacing. When the old rack rivets are drilled out. Use a sharpie and a straight edge to mark a line thru the old rivet locations. This line is then used when aligning and drilling the new rivet locations. This gear is molded from 30% glass filled polypropylene plastic. The buyer will need to break the gear sections loose from the sprues. 24.00 USD https://stigodiy.bigcartel.com/product/shopsmith-non-oem-rack-gear-replacement https://assets.bigcartel.com/product_images/406835925/IMG_5401.JPG https://assets.bigcartel.com/product_images/406835928/IMG_5400.JPG,https://assets.bigcartel.com/product_images/406835931/IMG_3579.JPG,https://assets.bigcartel.com/product_images/406835934/IMG_3578.JPG 114130653 new in stock 114130623 FOX and Smithy SuperShop spline shaft adapters for shopsmith This Super Shop spline shaft power coupler is being offered for FOX or Smithy owners that have a need to drive shopsmith accessories. The coupler attaches to either the 8 or 10 spline output shaft of the drive head or the clevis shaft joiner output shaft and provides a 4 or 5 spline shopsmith compatible drive stub. It is a monolithic 3D print using ABS plastic. When you purchase please specify whether you need the 8 or 10 spline or clevis shaft. Also specify the number of shopsmith splines. A single adapter is what will be shipped. Do not use a coupler that shows any signs of delamination, cracks or visible defects. Do not attempt to repair. I am liable only to the extent of the purchase price of this part. Use at your own risk. There is inherent danger using any wood working equipment, loads, speeds, feeds, unbalance and setups are determined by the user. If you do not agree to the limits of my liability please do not purchase this item. If you are not happy with this for any reason with 30 days of purchase, please contact me about a refund. This is not related to the Shopsmith company or any Shopsmith authorized retailer in any way. And probably would not be recommended for use by Shopsmith. The same would be true of the Fox or Smithy or Detroit Tool manufacturers as well. 24.13 USD https://stigodiy.bigcartel.com/product/fox-and-smithy-supershop-spline-shaft-adapters-for-shopsmith https://assets.bigcartel.com/product_images/406835847/IMG_3484.JPG https://assets.bigcartel.com/product_images/406835844/IMG_3480.JPG,https://assets.bigcartel.com/product_images/406835850/IMG_3483.JPG,https://assets.bigcartel.com/product_images/406835853/IMG_3500.JPG,https://assets.bigcartel.com/product_images/406835856/IMG_3481.JPG 114130623 new in stock 114130590 floating tramp oil pillow qty 3 Oil absorbent pillow approximately 10 x 10 x 2 inches, quantity 3. Will absorb oil that floats on the top of your full or partial synthetic water based coolant reservoir. I use these on my Tormach PCNC1100. 26.00 USD https://stigodiy.bigcartel.com/product/floating-tramp-oil-pillow-qty-3 https://assets.bigcartel.com/product_images/406835718/tramp-oil-pillow.JPG 114130590 new in stock 114125016 Steelcase drawer anti friction element sets These 3D printed anti friction elements are for a steelcase desk. Included are the elements to repair one desk drawer. I have provided some photos that were provided to me by customers of their steelcase desks using these anti friction elements. Hopefully it will assure that you are purchasing the correct part for your desk. I haven't ever owned one of these desks, I created the designs from parts that were provided to me by customers. Keep in mind that clearances of the OEM friction elements are pretty large, my FDM 3D printed parts are not any tighter. If you are hoping for a more modern feeling drawer, these parts will not provide any smoother operation. However they are great to replace missing or broken or worn elements. These are similar to the replacement parts that are offered on shapeways.com except they are printed using an ABS or PLA plastic using the FDM 3D printing process instead of a SLS process using nylon material with a smoother finish. Please contact me if you have another "impossible to find" part, I can probably help you, especially if it appears other people would be interested in it. 18.00 USD https://stigodiy.bigcartel.com/product/steelcase-drawer-anti-friction-element-sets https://assets.bigcartel.com/product_images/406817163/IMG_6113.jpg https://assets.bigcartel.com/product_images/406817157/icm_fullxfull.364702850_50uvl6vxrrswo8k0s8kw.jpg,https://assets.bigcartel.com/product_images/406817160/icm_fullxfull.222661162_fxno88ttz2o8kk4so880.jpg 114125016 new in stock 114124977 Ball bearing upgrade steelcase tanker desk drawer roller narrow style These ball bearing rollers are for replacing missing or broken rollers (o-ring style) on your antique steelcase tanker desk. Rolling smoothness is greatly improved over the original design. These rollers press onto the axles The bearings are shielded to assure long life of smooth rolling. The plastic adapter parts are CNC machined plastic. Color of the rollers may vary from the photo. The kit comes with 4 ball bearings, 2 large roller OD adapters, 2 large roller ID adapters, and 2 small roller ID adapters. These combine to make large and small roller assemblies. The large rollers attach to the desk base and the small rollers attach to the drawer. The kit repairs one drawer. The machined adapters easily press onto the bearings and desk axles. There are at least two distinct styles of rollers for Steelcase desks. This is the O-ring style, both the desk and drawer axles are the same and use retainers. There is another version which the rollers are narrower, and don't have o-rings, the small diameter rollers use a retainer, the large diameter rollers do not. Please examine the roller axles to verify, especially if you are missing all your rollers. If the axles are different between the drawer and the desk base then you need the narrow roller set. I designed these at the request of a customer. Perhaps they will be what you need too. Please measure the pin diameter, if these rollers fit your desk the pins are about 0.283 inches or 7.25mm in diameter. Drilling of the replacement rollers shouldn't be necessary, please contact me if the rollers don't fit or turn freely. For a description of how to install these please see the following youTube video: youTube Video Please contact me if you have another "impossible to find" part, I can probably help you, especially if it appears other people would be interested in it. 18.00 USD https://stigodiy.bigcartel.com/product/ball-bearing-upgrade-steelcase-tanker-desk-drawer-roller-narrow-style https://assets.bigcartel.com/product_images/406817100/narrow-style-kit-contents.JPG https://assets.bigcartel.com/product_images/406817097/narrow-big-roller-comparison.JPG,https://assets.bigcartel.com/product_images/406817094/narrow-style-axle-description.JPG,https://assets.bigcartel.com/product_images/406817103/narrow-small-roller-comparison.JPG 114124977 new in stock 114124953 Ball bearing upgrade steelcase tanker desk drawer roller o-ring style These ball bearing rollers are for replacing missing or broken rollers (o-ring style) on your antique steelcase tanker desk. Rolling smoothness is greatly improved over the original design. These rollers press onto the axles The bearings are shielded to assure long life of smooth rolling. The plastic adapter parts are custom molded plastic. Color of the rollers may vary from the photo. The kit comes with 4 ball bearings, 2 large roller OD adapters, 2 large roller ID adapters, and 2 small roller ID adapters. These combine to make large and small roller assemblies. The large rollers attach to the desk base and the small rollers attach to the drawer. The kit repairs one drawer. The adapter parts come attached with the molding spider, parts can be removed from the spider easily, the molded adapters easily press onto the bearings and desk axles. There are at least two distinct styles of rollers for Steelcase desks. This is the O-ring style, both the desk and drawer axles are the same and use retainers, see the listing photo. There is another version which the rollers are narrower, and don't have o-rings, the small diameter rollers use a retainer, the large diameter rollers do not. Please examine the roller axles to verify, especially if you are missing all your rollers. If the axles are different between the drawer and the desk base look at my narrow roller listing. I tried finding replacement parts for my steelcase desk and couldn't find them. So I designed these. Perhaps they will be what you need too. Please measure the pin diameter, if these rollers fit your desk the pins are about 0.283 inches or 7.25mm in diameter. Drilling of the replacement rollers shouldn't be necessary, please contact me if the rollers don't fit or turn freely. For a description of how to install these please see the following youTube video: youTube Video Please contact me if you have another "impossible to find" part, I can probably help you, especially if it appears other people would be interested in it. 18.00 USD https://stigodiy.bigcartel.com/product/ball-bearing-upgrade-steelcase-tanker-desk-drawer-roller-o-ring https://assets.bigcartel.com/product_images/406816950/kit-contents.JPG https://assets.bigcartel.com/product_images/406816947/roller-installation-on-desk.JPG,https://assets.bigcartel.com/product_images/406816944/big-roller-comparison.JPG,https://assets.bigcartel.com/product_images/406816953/small-roller-comparison.JPG 114124953 new in stock 114124887 NEW 2025! Sortimo Bosch L-Boxx base mounting mount bracket clip 3 sets Three pairs of mounting brackets for Sortimo, Bosch L-BOXX tool and storage cases, low profile footprint, with a good nesting function. Brackets may be used to secure the L-BOXX on a shelf, rolling cart, dolly, wall or counter top type installation by creating a mounting nest. The L-BOXX snaps onto the locating features. Each bracket has 4 clearance holes which will work with up to a #10 flat head fastening screw. These brackets are manufactured by injection molding. This clip set is more than 5X stronger Uses 4 #10 flat head screws to attach. Injection molding is far superior to 3D printed mounts. 3D printed mounts are like wood, the layers of the printer are weaker, just like a wooden board is much weaker across the grain than with the grain. These brackets are constructed of glass filled polypropylene which has better impact strength and are suitable for the high temperatures of a work van or truck in the hot summer sun, 3d printed plastics such as PLA and HIPS will stress relieve in the higher temperatures. For instance if the clip system is used on a wall or ceiling, the load of the L-BOXX will cause a PLA or HIPS plastic part to deform to the point of failure. PLA is more brittle and fractures more easily under an impact load as well. Preliminary load testing with a Sortimo L-BOXX model 102 holds in excess of 220 lbs tension without any sign of failure or excessive deflection. Keep in mind that road bumps can easily create g-loads in excess of 4g, which in effect increases the weight of the sortimo box by over a factor of 4. If you are traveling with stacked boxes in the clips, put the heaviest box on the bottom. 17.97 USD https://stigodiy.bigcartel.com/product/new-2025-sortimo-bosch-l-boxx-base-mounting-mount-bracket-clip-3-sets https://assets.bigcartel.com/product_images/406816854/qty3-natural-off-sprue.jpeg https://assets.bigcartel.com/product_images/406816845/clips-w-lbox.jpeg,https://assets.bigcartel.com/product_images/406816848/clips-w-lbox2.jpeg,https://assets.bigcartel.com/product_images/406816851/clips-on-board.jpeg 114124887 new in stock 114124848 Table insert for Shopsmith Scroll/Jig Saw Replacement qty 2 model 610 Magna 18 This replacement table insert is 3D printed in plastic, color may vary. The package contains two inserts as these are a wear item and may wear out quicker if the saw is used by an inexperienced operator. Like the OEM die cast insert, it will support the extremes of table tilt due to the chamfers on the bottom side of the insert. This may also fit the jig saw as well as the Magna 18" scroll saw. 17.88 USD https://stigodiy.bigcartel.com/product/table-insert-for-shopsmith-scrolljig-saw-replacement-qty-2-model-610-magna-18 https://assets.bigcartel.com/product_images/406816704/image3.jpeg https://assets.bigcartel.com/product_images/406816698/image2.jpeg,https://assets.bigcartel.com/product_images/406816701/image1.jpeg,https://assets.bigcartel.com/product_images/406816707/image0.jpeg 114124848 new in stock 114124824 Yoke Slider for Shopsmith Scroll/Jig Saw Replacement qty 2 model 610 This replacement yoke slider is 3D printed from ABS. The package contains two sliders as these are a wear item and may wear out quicker depending on how well lubricated. Here is a link to a YouTube video showing how easy it is to replace it on the Shopsmith model 610: YouTube Replacement tutorial The nameplate indicates SAE10 oil should be used. The nameplate has to be removed to access the fill plug. Another 3D printed option uses nylon material, the design is available thru shapeways.com. It looks more like the original design except I thickened the walls. If you are interested, a search on that website should find it. 17.88 USD https://stigodiy.bigcartel.com/product/yoke-slider-for-shopsmith-scrolljig-saw-replacement-qty-2-model-610 https://assets.bigcartel.com/product_images/406816665/yoke-slider.JPG https://assets.bigcartel.com/product_images/406816662/abs-yoke-on-ss.JPG,https://assets.bigcartel.com/product_images/406816668/original-yoke.JPG 114124824 new in stock 114124788 elfa caster wheel mount clip Elfa and the container store don't offer this part to fix your cherished roll around storage shelf or hanging file, I guess the company would prefer that you buy the latest design and throw away the one you have and send it to the land fill. I created a replacement that is reinforced so that it won't break as easily. It is very easy to replace and will get you rolling again. The purchase includes two replacement parts. 17.68 USD https://stigodiy.bigcartel.com/product/elfa-caster-wheel-mount-clip https://assets.bigcartel.com/product_images/406816551/list-photo1.JPG https://assets.bigcartel.com/product_images/406816554/list-photo2.JPG,https://assets.bigcartel.com/product_images/406816548/list-photo4.JPG,https://assets.bigcartel.com/product_images/406816560/list-photo3.JPG,https://assets.bigcartel.com/product_images/406816557/list-photo5.JPG 114124788 new in stock 114124752 harvest FLO SHELF TM DTC-1 drain tube cover qty 4 Here is a great gift idea for your Honey that keeps bees. Soon it will be time to harvest left over winter honey, or the first nectar flows of spring. This harvest FLO shelf TM drain cover tool keeps ants, bees and wasps out of the honey harvest flow from either a Australian "FLOW" or Chinese "Autoframe" style hives. Even though the shape and dimensions of the two different artificial honeycomb drain tubes are different, this 3D printed accessory fits both. The drain cover tool doesn't contact the honey during gravity only harvest. This tool honey works with either recap style mason jar lids or a user modified mason jar lid. I developed this after my first harvest where I ended up with more than a dozen bees in each honey collection container. After some fruitless searching I determined that no off the shelf plumbing elbow was available, plus any type of conventional elbow increases the flow resistance due to the increased wetted flow area, hence the harvest time could be increased, and if the comb isn't fully capped, the flow can backup enough to cause internal honey leakage in hive, even just using the drain tube alone, much less adding any flow resistance with a plumbing elbow. This drain cover tool can optionally be used in conjunction with vacuum assistance to speed the honey flow during initial opening, which can minimize internal flow backup if partially capped honeycomb exists, resulting in significant honey leakage inside the hive, causing a temporary exodus of worker bees. If used with vacuum, the honey will contact the drain cover tool, so proper cleaning before and after use are recommended. Click this link for a video about this product Click this link for a video showing vacuum assisted honey harvest You will receive the following: qty 4- Drain tube cover made by 3D printer out of ABS plastic This listing does NOT include, any drain tube, harvest shelf or artificial honeycomb or other langstroth hive components which are shown in some of the listing photos. This product has a patent pending, please contact me if you are interested in manufacturing and marketing this concept under a licensing agreement. Designed and Manufactured in Dallas, TX by Stig O'DIY +/- Design Note that this product is 3D printed using natural colored ABS, rather than injection molding. As a result the part you will receive has a layered appearance that makes some of cylindrical surfaces have a discretized coarse appearance which does not affect its intended function. The drain cover will not seal perfectly due to porosity in the layered print structure, however it will keep ants, bees and wasps out of the honey. The porosity will not adversely affect the vacuum assist capability either. If for some reason you need a drain tube cover that has no porosity or is visually perfect or of a different color, this design is available on shapeways.com, just search for "harvest FLO SHELF TM drain tube cover" on the shapeways website. The shapeways.com part is made from nylon, colors other than white are dyed after build. The wall thickness of the shapeways.com version is 33% less, to make the part more affordable, as material weight is a cost driver. 16.79 USD https://stigodiy.bigcartel.com/product/harvest-flo-shelf-tm-dtc-1-drain-tube-cover-qty-4 https://assets.bigcartel.com/product_images/406816425/drain-cover-qty4.JPG https://assets.bigcartel.com/product_images/406816413/DCT-both-drain-tubes.JPG,https://assets.bigcartel.com/product_images/406816416/DCT-inside-closeup.JPG,https://assets.bigcartel.com/product_images/406816422/honey-flowing-in-dtc.JPG,https://assets.bigcartel.com/product_images/406816419/DTC1-on-hives.JPG 114124752 new in stock 114124728 Power Coupler Square Dowel for Shopsmith This coupler is for a standard shopsmith that has a drive hub with 4 grooves and the accessory hub has 5 grooves. New in April of 2022, this item is now injection molded, providing a superior product with better strength characteristics and more consistent fit and finish. Color may vary from photo. This power coupler set allows a custom coupling length, as short as 2.6 inches to as long as 38 inches, the standard coupler is 5 inches long. These parts are molded, using a glass filled polypropylene material. 3/4 inch square wood dowel may be cut to desired length. Use of a softer wood is advised, as the wood is cheaper than the adapter to replace if an overloading event happens. The coupler ends are retained with the provided screws. Torque testing with a knot free poplar wood dowel purchased at Lowes showed to have in excess of 13 ft-lbs strength before the wood dowel broke. Using a metal rod will have a breaking strength in excess of 35 ft-lbs. I developed a new molded design because some of my customers were able to break the 3D printed coupler during their ordinary use. The ABS 3D printed design was usually okay but some accessories and uses could cause issues with more hardcore user. The belt sander accessory is the hardest on my 3D printed couplers. There are a number of potential issues. First is centering alignment between the headstock and beltsander, it needs to be very good, preferably less than 1/16 of an inch, also the length of the dowel needs to be on the longer end, probably 1.5X the OEM coupler length. If not aligned there will be plastic debris from internal grinding. Another possible issue is shaft runout (slightly bend of shaft) on the beltsander, as an accessory sometimes things get accidently bent, which would exhibit itself as grinding too. Aligning the shafts isn't difficult but will take several minutes to an hour depending on how rusty things are. Both vertical and horizontal centering can be adjusted. Another Belt sander concern is belt tension, especially if the rubber roller has age hardened. People tend to tension it greater, which dramatically increases the torque load, this might be evident by the headstock struggling on start up. While my 3D couplers have good static torque strength, they did not hold up with cyclic fatigue stress from mis-alignment, and high drag from excessive belt tension, particularly if one or more of the couplers has snug fit on one of the stub ends and a snug fit at the wood dowel interface. If the coupler gets "wear in" at lighter loads on an accessory like a bandsaw, to loosen up the fits, they can hold up better, but still it is only a matter of time before grinding takes off the nubs inside of the coupler unless shaft centering is adjusted. The new molded design should hold up far better to misalignment due to the glass filler in the resin. If you have doubts about compatibility with your belt sander, the OEM Shopsmith coupler may be a better option. Shopsmith claims their coupler is indestructable. My 3D printed one wasn't, however my new molded coupler might be indestructable. The following YouTube video shows the adaptable coupler running over the range of speeds and shows that a shorter wood dowel should be used when running at the high RPM's of a joiner or planer. https://www.youtube.com/watch?v=hEg36ctsjWc (if the link doesn't work search for: power couplers in use ) The following YouTube video shows comparative strength testing of power couplers (Hopefully I will be updating soon with the next generation couplers): https://www.youtube.com/watch?v=F22xO0QOZbM (if the link doesn't work search for: Shopsmith Power Coupler Testing: Part1 Summary Results ) https://www.youtube.com/watch?v=UL4M1D6Ie1c (if the link doesn't work search for: Shopsmith Power Coupler Torque Testing: Part 2 All Tests ) https://www.youtube.com/watch?v=CscRqpZKiFQ (if the link doesn't work search for: Shopsmith power coupler testing part3 retest and redemption) If you purchase the wrong adapter for your shopsmith and need to exchange for the correct one, the incorrect one will need to be sent back for a refund and the correct style purchased under a separate transaction. When the incorrect item is received a refund will be issued minus a fee of $4 which covers my cost for the initial shipping. Rather than buying dowel, the user could also rip his own 3/4 inch square wood dowel stock as well. Wood dowel at Lowe's or Home Depot < $4 for a 36 inch long dowel. Use of a soft knot free pine is recommended rather than a higher strength wood like oak or hickory. I am liable only to the extent of the purchase price of this part. Use at your own risk. There is inherent risk using any Shopsmith equipment, loads, imbalance, speeds, feeds, and setups are determined by the user. If you do not agree to the limits of my liability please do not purchase this item. If you are not happy with this item for any reason within 30 days of purchasing contact me for details on getting a refund. This power coupler is not related to the shopsmith company or any authorized retailer of shopsmith equipment in any way and would not be endorsed for use with shopsmith equipment. 16.78 USD https://stigodiy.bigcartel.com/product/power-coupler-square-dowel-for-shopsmith https://assets.bigcartel.com/product_images/406816218/IMG_4870.JPG https://assets.bigcartel.com/product_images/406816338/IMG_2091.JPG 114124728 new in stock 114124686 Steelcase Pedastal File drawer roller replacement This is a 3D printed replacement for a Steelcase filing cabinet drawer 16.50 USD https://stigodiy.bigcartel.com/product/steelcase-pedastal-file-drawer-roller-replacement https://assets.bigcartel.com/product_images/406816065/steelcase-file-drawer-roller-replacement.jpg https://assets.bigcartel.com/product_images/406816062/steelcase-file-drawer-roller-compare.jpg 114124686 new in stock 114124674 Power Coupler 3/4 PVC pipe for Shopsmith 2024 Design This coupler is for a standard shopsmith that has a drive hub with 4 grooves and the accessory hub has 5 grooves. New in February of 2024, this item is now injection molded, providing a superior product with better strength characteristics and more consistent fit and finish. Color may vary from photo. This power coupler set allows a custom coupling length, as short as 2.6 inches to as long as 38 inches, the standard coupler is 5 inches long. These parts are molded, using a glass filled polypropylene material. 3/4 inch PVC pipe may be cut to desired length. Bonding of the coupler is best using a high strength epoxy such a JB Weld "steel", prepping the pipe and coupler by scuffing the bond surfaces using 80 to 220 grit sandpaper and applying epoxy to both the pipe and coupler ends before joining will result in the highest strength bond. A better quality super glue (cyanoacrylic adhesive) could work as well, I tried harbor freight "gel" and it wasn't as strong as epoxy. PVC will work but the bond strength isn't great. My strength testing showed the bond joints breaking first, leaving the coupler and pipe undamaged. I am bringing back a PVC pipe version because some customers liked it over the wood dowel version. I developed a new molded design because some of my customers were able to break the 3D printed coupler during their ordinary use. The ABS 3D printed design was usually okay but some accessories and uses could cause issues with more hardcore user. The belt sander accessory is the hardest on my 3D printed couplers. There are a number of potential issues. First is centering alignment between the headstock and beltsander, it needs to be very good, preferably less than 1/16 of an inch, also the length of the dowel needs to be on the longer end, probably 1.5X the OEM coupler length. If not aligned there will be plastic debris from internal grinding. Another possible issue is shaft runout (slightly bend of shaft) on the beltsander, as an accessory sometimes things get accidently bent, which would exhibit itself as grinding too. Aligning the shafts isn't difficult but will take several minutes to an hour depending on how rusty things are. Both vertical and horizontal centering can be adjusted. Another Belt sander concern is belt tension, especially if the rubber roller has age hardened. People tend to tension it greater, which dramatically increases the torque load, this might be evident by the headstock struggling on start up. While my couplers have good static torque strength, they did not hold up with cyclic fatigue stress from mis-alignment, and high drag from excessive belt tension, particularly if one or more of the couplers has snug fit on one of the stub ends and a snug fit at the wood dowel interface. If the coupler gets "wear in" at lighter loads on an accessory like a bandsaw, to loosen up the fits, they can hold up better, but still it is only a matter of time before grinding takes off the nubs inside of the coupler unless shaft centering is adjusted. The new molded design should hold up far better to misalignment due to the glass filler in the resin. If you have doubts about compatibility with your belt sander, the OEM Shopsmith coupler may be a better option. Shopsmith claims their coupler is indestructable. My 3D printed one wasn't, however my new molded coupler might be indestructable. The following YouTube video shows the adaptable coupler running over the range of speeds and shows that a shorter wood dowel should be used when running at the high RPM's of a joiner or planer. https://www.youtube.com/watch?v=hEg36ctsjWc (if the link doesn't work search for: power couplers in use ) The following YouTube video shows comparative strength testing of power couplers (Hopefully I will be updating soon with the next generation couplers): https://www.youtube.com/watch?v=F22xO0QOZbM (if the link doesn't work search for: Shopsmith Power Coupler Testing: Part1 Summary Results ) https://www.youtube.com/watch?v=UL4M1D6Ie1c (if the link doesn't work search for: Shopsmith Power Coupler Torque Testing: Part 2 All Tests ) https://www.youtube.com/watch?v=CscRqpZKiFQ (if the link doesn't work search for: Shopsmith power coupler testing part3 retest and redemption) If you purchase the wrong adapter for your shopsmith and need to exchange for the correct one, the incorrect one will need to be sent back for a refund and the correct style purchased under a separate transaction. When the incorrect item is received a refund will be issued minus a fee of $4 which covers my cost for the initial shipping. Rather than buying dowel, the user could also rip his own 3/4 inch square wood dowel stock as well. Wood dowel at Lowe's or Home Depot < $4 for a 36 inch long dowel. Use of a soft knot free pine is recommended rather than a higher strength wood like oak or hickory. I am liable only to the extent of the purchase price of this part. Use at your own risk. There is inherent risk using any Shopsmith equipment, loads, imbalance, speeds, feeds, and setups are determined by the user. If you do not agree to the limits of my liability please do not purchase this item. If you are not happy with this item for any reason within 30 days of purchasing contact me for details on getting a refund. This power coupler is not related to the shopsmith company or any authorized retailer of shopsmith equipment in any way and would not be endorsed for use with shopsmith equipment 16.24 USD https://stigodiy.bigcartel.com/product/power-coupler-34-pvc-pipe-for-shopsmith-2024-design https://assets.bigcartel.com/product_images/406816002/molded-pvc-coupler-1.JPG https://assets.bigcartel.com/product_images/406816005/molded-pvc-coupler-3.JPG,https://assets.bigcartel.com/product_images/406815999/molded-pvc-coupler-2.JPG 114124674 new in stock 114124635 replacement speedometer gear schwinn air dyne qty 2 This is a 3D printed speedometer gear that should revive your classic air dyne speedometer. The shaft is .25 inch diameter, the square drive is for a speedometer cable that is .100 inch across the flats. Troubleshooting your bike. Disconnect the speedometer cable at the fan hub. Move pedals slowly, if the square drive isn't rotating, the teeth of the gear are probably sheared off. Quick and easy way to replace is to bend the speedometer cable tab up enough that the old gear shaft can push out. Clean bore with cotton swab and alcohol. Lightly oil new gear shaft, insert and bend tab back. Move pedals verify shaft is turning properly. Reconnect speedometer cable and enjoy. 16.00 USD https://stigodiy.bigcartel.com/product/replacement-speedometer-gear-schwinn-air-dyne-qty-2 https://assets.bigcartel.com/product_images/406815840/image0.jpeg https://assets.bigcartel.com/product_images/406815837/image5.jpeg,https://assets.bigcartel.com/product_images/406815843/image3.jpeg,https://assets.bigcartel.com/product_images/406815846/image1.jpeg,https://assets.bigcartel.com/product_images/406815849/image2.jpeg 114124635 new in stock 114124611 Delta 40-150 15" scroll saw drive link replacement This is a machined aluminum replacement part. One link is included with your purchase. 18.00 USD https://stigodiy.bigcartel.com/product/delta-40-150-15-scroll-saw-drive-link-replacement https://assets.bigcartel.com/product_images/406815597/alum-compare-to-oem.jpg https://assets.bigcartel.com/product_images/406815600/IMG_2615.jpg,https://assets.bigcartel.com/product_images/406815603/IMG_2618.jpg,https://assets.bigcartel.com/product_images/406815606/IMG_2617.jpg,https://assets.bigcartel.com/product_images/406815609/IMG_2616.jpg 114124611 new in stock 114124584 Mid century modern desk drawer roller set steelcase clone These 3D printed rollers on your antique steelcase clone desk. I don't know the manufactures name. Look closely at the rollers and compare to the rollers on your current desk. The axles the rollers ride on are about .37 inch in diameter. The FDM printing process I use is coarse, the appearance of the rollers is not as smooth as the original molded rollers, however the strength should be fine. You may need to deburr the parts, from the 3D printing process, which should only take a couple minutes. This roller set may fit other desks made by other manufacturers. If you have any doubts please contact me before purchasing and I will help you determine which rollers you need. Please send a photo of the roller mounts in your initial email. Included are the rollers and retainers to repair one desk drawer. Keep in mind that clearances of the OEM rollers are pretty large, my FDM 3D printed parts are not any tighter. If you are hoping for a more modern feeling drawer, these rollers will not provide any smoother operation. However they are great to replace missing or broken rollers. Please contact me if you have another "impossible to find" part, I can probably help you, especially if it appears other people would be interested in it. 16.00 USD https://stigodiy.bigcartel.com/product/mid-century-modern-desk-drawer-roller-set-steelcase-clone https://assets.bigcartel.com/product_images/406815498/IMG_3518.JPG https://assets.bigcartel.com/product_images/406815486/image6.jpeg,https://assets.bigcartel.com/product_images/406815489/image7.jpeg,https://assets.bigcartel.com/product_images/406815492/IMG_3517.JPG,https://assets.bigcartel.com/product_images/406815495/IMG_3516.JPG 114124584 new in stock 114124560 Nissan clutch pedal stopper 46512-9BP1C non-OEM durable replacement qty2 This stopper gets damaged by the clutch switch over time. When it fails the vehicle will no longer start because the switch isn't depressed properly by the stop. This is a 3d printed plastic version that should last longer than the OEM rubber part. Purchase includes 2 parts, one fits a 1/4 hole the other fits a .312 hole. 15.00 USD https://stigodiy.bigcartel.com/product/nissan-clutch-pedal-stopper-46512-9bp1c-non-oem-durable-replacement-qty2 https://assets.bigcartel.com/product_images/411752955/nissan-clutch-stop-2sizes.jpeg https://assets.bigcartel.com/product_images/406815447/listing2.jpg,https://assets.bigcartel.com/product_images/406815444/listing3.jpg 114124560 new in stock 114124494 Shopsmith Power Coupler Coupling time saver stub See the setup timesaver in action in the following YouTube video: https://youtu.be/cshvo6VwzKQ This set-up timesaver stub allows a quick transition from use of the headstock spindle to a power coupler driven accessory. This 3D printed part is versatile as it can be used with a drill chuck or any arbor mounted accessory with a 1/2" threaded shaft, 11/16" or 3/4" clamping nut. It is printed from ABS plastic. The time saver stub with the included bolt is used with the drill chuck. The unmounted time saver stub is used with an arbor mounted accessory like a grinding wheel, flap disk wheel, wire wheel, etc. Is even easier and quicker as the stub end slips over the locking nut of the accessory and is retained between the power coupling and adjoining accessories. The arbor nut must be torqued to greater than 5 ft-lbs. Do not use a stub that shows any signs of delamination, cracks or visible defects. Do not attempt to repair the stub. I am liable only to the extent of the purchase price of this part. There is inherent risk using any Shopsmith equipment, loads, imbalance, speeds, feeds, and setups are determined by the user. If you do not agree to the limits of my liability please do not purchase this item. This set-up time saving stub is not a related to the shopsmith company or any authorized retailer of shopsmith equipment in any way and probably would not be endorsed for use with shopsmith equipment. 14.88 USD https://stigodiy.bigcartel.com/product/shopsmith-power-coupler-coupling-time-saver-stub https://assets.bigcartel.com/product_images/406815234/orig-stub3.JPG https://assets.bigcartel.com/product_images/406815240/orig-stub4.JPG,https://assets.bigcartel.com/product_images/406815237/orig-stub7.JPG,https://assets.bigcartel.com/product_images/406815243/orig-stub5.JPG,https://assets.bigcartel.com/product_images/406815246/orig-stub9.JPG 114124494 new in stock 114124482 Bamboo Roman shade repair clip and ring 12 pairs Included are 12 clips and 12 rings. The rings are split to allow easy installation onto your shade's pull string, just make sure the split is inserted into the clip. The old clips were prone to breaking due to pets, careless children and the housecleaner. I looked in hardware stores, online and couldn't find replacements, so I designed my own stronger version and printed on my 3D printer using ABS plastic. I started a new ebay ID for selling 3D printed parts, I have been buying and selling on ebay since 2001 with a 100% satisfaction rating. If you have a similar clip but of a different design which can't be procured someplace else, I would consider doing a custom design for you. 14.00 USD https://stigodiy.bigcartel.com/product/bamboo-roman-shade-repair-clip-and-ring-12-pairs https://assets.bigcartel.com/product_images/406815108/roman-shade-clip.JPG https://assets.bigcartel.com/product_images/406815111/roman-shade-clip2.JPG 114124482 new in stock 114124449 Extra Short Power Coupler for Shopsmith 2022 Molded Design!!! This robust extra short power coupler is being offered for Shopsmith owners that have a need for a very short coupler. The coupler has an overall length of less than 1.20 inches versus the OEM coupler that is 5 inches long. This coupler will allow the hub of the accessory to touch the drive hub. It is a molded part as of April 2022, replacing the previous 3d printed part. The molded part is made of a glass filled polypropylene. My torque testing shows a strength of 40 ft-lb. Wear should be much improved over the previous ABS part due to the glass filler. Keep in mind the shaft alignments need to be much closer since the length is very short. Misalignment causes asymmetrical loading at best and interference at its worse. Misalignment will likely cause premature failure due to wear. The belt sander accessory is the hardest on my 3D printed couplers. There are a number of potential issues. First is centering alignment between the headstock and beltsander, it needs to be very good, preferably less than 1/16 of an inch, also the length of the dowel needs to be on the longer end, probably 1.5X the OEM coupler length. If not aligned there will be plastic debris from internal grinding. Another possible issue is shaft runout (slightly bend of shaft) on the beltsander, as an accessory sometimes things get accidently bent, which would exhibit itself as grinding too. Aligning the shafts isn't difficult but will take several minutes to an hour depending on how rusty things are. Both vertical and horizontal centering can be adjusted. Another Belt sander concern is belt tension, especially if the rubber roller has age hardened. People tend to tension it greater, which dramatically increases the torque load, this might be evident by the headstock struggling on start up. https://www.youtube.com/watch?v=hEg36ctsjWc https://www.youtube.com/watch?v=F22xO0QOZbM https://www.youtube.com/watch?v=UL4M1D6Ie1c (if the link doesn't work search for: power couplers in use ) I am liable only to the extent of the purchase price of this part. Use at your own risk. There is inherent danger using any Shopsmith equipment, loads, speeds, feeds, unbalance and setups are determined by the user. If you do not agree to the limits of my liability please do not purchase this item. If you are not happy with this for any reason with 30 days of purchase, please contact me about a refund. This is not related to the Shopsmith company or any Shopsmith authorized retailer in any way. And probably would not be recommended for use by Shopsmith. 13.93 USD https://stigodiy.bigcartel.com/product/extra-short-power-coupler-for-shopsmith-2022-molded-design https://assets.bigcartel.com/product_images/406814985/IMG_4871.JPG https://assets.bigcartel.com/product_images/406814979/extra-short-xsec.JPG,https://assets.bigcartel.com/product_images/406814982/IMG_4873.JPG 114124449 new in stock 114124404 Mid century modern desk drawer roller set Anderson Hickey These 3D printed rollers and retainers are for replacing missing or broken rollers on your antique Anderson Hickey Furniture company desk. The FDM printing process I use is coarse, the appearance of the rollers is not the same as the original molded rollers, however the strength should be fine. You will need to deburr the parts, from the 3D printing process, which should only take a couple minutes. This roller set may fit other desks made by other manufacturers. If you have any doubts please contact me before purchasing and I will help you determine which rollers you need. Please send a photo of the roller mounts in your initial email. Included are the rollers and retainers to repair one desk drawer. Keep in mind that clearances of the OEM rollers are pretty large, my FDM 3D printed parts are not any tighter. If you are hoping for a more modern feeling drawer, these rollers will not provide any smoother operation. However they are great to replace missing or broken rollers. Please contact me if you have another "impossible to find" part, I can probably help you, especially if it appears other people would be interested in it. 13.12 USD https://stigodiy.bigcartel.com/product/mid-century-modern-desk-drawer-roller-set-anderson-hickey https://assets.bigcartel.com/product_images/406814829/ahfc-rollers-1.JPG https://assets.bigcartel.com/product_images/406814817/ahfc-rollers-2.JPG,https://assets.bigcartel.com/product_images/406814820/ahfc-rollers-3.JPG,https://assets.bigcartel.com/product_images/406814826/ahfc-rollers-4.JPG,https://assets.bigcartel.com/product_images/406814823/ahfc-rollers-5.JPG 114124404 new in stock 114124362 Temporary queen bee excluder for top bar hive or swarm capture box This queen excluder design is intended for temporary use when first introducing a swarm to a new top bar hive or while temporarily housing the swarm after capture in a cardboard box. The queen excluder also has a closure hatch as well to allow easy transportation. With two screw holes, mounting is possible for either a top bar hive or swarm capture box. The queen excluder is sized to approximately .154" wide slots. Other sizes could be made available upon request. This slot width has worked pretty well for me in Texas. I sized the opening to 1 inch in diameter. This is a 3D printed design using PLA plastic. Included are three excluders. If you are not happy with this product please contact me within 30 days of receipt for details to receive a refund. 14.00 USD https://stigodiy.bigcartel.com/product/temporary-queen-bee-excluder-for-top-bar-hive-or-swarm-capture-box https://assets.bigcartel.com/product_images/406815132/IMG_1830.JPG https://assets.bigcartel.com/product_images/406814628/queen-exc-qty3.JPG,https://assets.bigcartel.com/product_images/406814622/queen-excl-swarm-box.JPG,https://assets.bigcartel.com/product_images/406814625/queen-excl-hive2.JPG,https://assets.bigcartel.com/product_images/406815147/IMG_1829.JPG 114124362 new in stock 114124323 Shure E3C earphone repair qty 2 I love my Shure e3c sound isolating earphones, the sound quality is great, the durability of the cord is phenomenal. I have had them for years, they are my go to earphones when traveling, or working with noisy equipment. I was disappointed when I accidentally broke the tube off when working in the shop one day. So I designed a repair part that bonds onto the earphone and provides the tubular mounting feature that the soft earpieces slip over. The repair slightly increases the length of the earbud, but the length increase is required to create a large enough bond area for a strong bond joint. I tend to used the very small ear adapters and I did not notice any change in comfort level after repair. The sound quality seems as good as before as well. I used a "gel" type cyanoacrylic adhesive (a.k.a. super glue) and it seems to hold well. An epoxy would also be a good choice if you stay away from the quick setting types. I cleaned the earphone end using an acetone wetted paper towel. This repair may work for other Shure models that use the same adapters. The repair parts are made from ABS, using an FDM 3D printing process. 12.00 USD https://stigodiy.bigcartel.com/product/shure-e3c-earphone-repair-qty-2 https://assets.bigcartel.com/product_images/406814508/IMG_2516.JPG https://assets.bigcartel.com/product_images/406814505/DSCN0023.JPG,https://assets.bigcartel.com/product_images/406814511/DSCN0021.JPG,https://assets.bigcartel.com/product_images/406814514/DSCN0020.JPG 114124323 new in stock 114123849 Steelcase tanker desk center drawer roller set This is a set of rollers to rework the center drawer of a steelcase desk with o-ring style rollers on the side drawers. Other models of steelcase desks may use the same roller. The steel axles that the rollers ride on are 5/16" in diameter and a little longer than 3/8 of an inch. On my desk the old rollers didn't turn freely and the friction from opening and closing the drawer wore flat spots on the rollers. 13.00 USD https://stigodiy.bigcartel.com/product/steelcase-tanker-desk-center-drawer-roller-set https://assets.bigcartel.com/product_images/406813170/IMG_3215.JPG https://assets.bigcartel.com/product_images/406813173/IMG_3214.JPG,https://assets.bigcartel.com/product_images/406813191/IMG_3212.JPG,https://assets.bigcartel.com/product_images/406813194/IMG_3213.JPG 114123849 new in stock 114123726 Tormach TTS Passive Probe Stow Mount Clip I created this to use with my Tormach PCNC 1100 Series 3. It allows the passive probe to be continually connected and stored out of the way from chips and coolant spray or mist. For me connecting and disconnecting the probe electrically is inconvenient and often messy. This stow clip can either be ceiling or wall mounted. The clip is made using a FDM 3D printer, the plastic is ABS. The color is natural, application photos used a bright colored plastic to allow better contrast for the photos. I use a light elastic strap connected to kitchen magnetized hook, to hold the electrical cable out of the way. Some fishing line and a sinker could be used as a counter weight to keep the electrical cable out of the way as well. 12.00 USD https://stigodiy.bigcartel.com/product/tormach-tts-passive-probe-stow-mount-clip https://assets.bigcartel.com/product_images/406812993/2020-stow-clip1.JPG https://assets.bigcartel.com/product_images/406812999/2020-stow-clip2.JPG,https://assets.bigcartel.com/product_images/406812990/2020-stow-clip3.JPG,https://assets.bigcartel.com/product_images/406812996/2020-stow-clip4.JPG,https://assets.bigcartel.com/product_images/406813002/2020-stow-clip5.JPG 114123726 new in stock 114123669 Improved Polaris Bag collar clip replaces 9-100-3135 I created this unique polaris bag collar clip design after I had two bags in row with deteriorated velcro attachments break in a couple days and not having any extra bags. The bags are perfectly useful except for the missing velcro strips. Of course the bag needs to be clipped to the hose to keep it from getting tangled up with the wheels. You could easily get another season or two from a collection bag with a missing velcro strap. When I was in Leslies today it looks like they are charging over $40 a bag. So I 3D printed this to fix it and I was thinking that other people might benefit from this design. You can either use the velcro straps like always or if the velcro straps are missing or don't stick, use the clip to hold it. This is FDM printed from ABS plastic so it holds up well in pool water and in the sun. Since it is 3D printed it has layered appearance. You purchase includes one clip. Contact me if you have a need for a similar niche product. 12.00 USD https://stigodiy.bigcartel.com/product/improved-polaris-bag-collar-clip-replaces-9-100-3135 https://assets.bigcartel.com/product_images/406812726/20202bagclip1.JPG https://assets.bigcartel.com/product_images/406812735/20202bagclip3.JPG,https://assets.bigcartel.com/product_images/406812729/20202bagclip2.JPG,https://assets.bigcartel.com/product_images/406812732/20202bagclip4.JPG 114123669 new in stock 114123642 Improved Polaris Bag collar clip replaces 9-100-1018 I created this unique polaris bag collar clip design after I had two bags in row with deteriorated velcro attachments break in a couple days and not having any extra bags. The bags are perfectly useful except for the missing velcro strips. Of course the bag needs to be clipped to the hose to keep it from getting tangled up with the wheels. You could easily get another season or two from a collection bag with a missing velcro strap. When I was in Leslies today it looks like they are charging over $40 a bag. So I 3D printed this to fix it and I was thinking that other people might benefit from this design. You can either use the velcro straps like always or if the velcro straps are missing or don't stick, use the clip to hold it. This is FDM printed from ABS plastic so it should hold up well in pool water and in the sun. Since it is 3D printed it has layered appearance.I created this unique polaris bag collar clip design after I had two bags in row with deteriorated velcro attachments break in a couple days and not having any extra bags. The bags are perfectly useful except for the missing velcro strips. Of course the bag needs to be clipped to the hose to keep it from getting tangled up with the wheels. You could easily get another season or two from a collection bag with a missing velcro strap. When I was in Leslies today it looks like they are charging over $40 a bag. So I 3D printed this to fix it and I was thinking that other people might benefit from this design. You can either use the velcro straps like always or if the velcro straps are missing or don't stick, use the clip to hold it. This is FDM printed from ABS plastic so it should hold up well in pool water and in the sun. Since it is 3D printed it has layered appearance. 12.00 USD https://stigodiy.bigcartel.com/product/improved-polaris-bag-collar-clip-replaces-9-100-1018 https://assets.bigcartel.com/product_images/406812627/listing2.JPG https://assets.bigcartel.com/product_images/406812615/listing1.JPG,https://assets.bigcartel.com/product_images/406812618/listing3.JPG,https://assets.bigcartel.com/product_images/406812621/listing5.JPG,https://assets.bigcartel.com/product_images/406812624/listing4.JPG 114123642 new in stock 114123480 110310800REIN non-OEM for Whirlpool washer or dryer handle wp8182574 PS982304 This aftermarket replacement is being offered to replace 110310800 which is used in a Whirlpool handle assembly, WP8182574 and may fit other handles as the whirlpool washer and dryers are re-branded and sold under other names such as Admiral, Amana, Carrier, Crosley, Estate, Hardwick, Jenn Air, Kenmore, Kitchen Aid, Magic Chef, Maytag, Norge, or Roper. Does not include an entire handle assembly. Buyer will only receive the one new part shown in the main photo. . This part was designed and manufactured in America, several chinese sellers are selling a copy of my design, that is molded in China. I am the original designer and supplier of these parts. I created several videos about replacing this, please consider this before buying the chinese copy. Included is a modified part which is reinforced to increase the force required to break, a quantity of one will be shipped. 12.00 USD https://stigodiy.bigcartel.com/product/110310800rein-non-oem-for-whirlpool-washer-or-dryer-handle-wp8182574-ps982304 https://assets.bigcartel.com/product_images/406812231/110310800-list1.JPG https://assets.bigcartel.com/product_images/406812234/110310800-list2.JPG,https://assets.bigcartel.com/product_images/406812237/110310800-list3.JPG,https://assets.bigcartel.com/product_images/406812240/110310800-list4.JPG,https://assets.bigcartel.com/product_images/406812243/110310800-list5.JPG 114123480 new in stock